Press Seal Type CMS30

Against pressing water and non-pressing water

Water-tight welded bolts for an optimum of steadiness and corrosion protection

Custom-made for customer-specific requirements

100% gas-, odor- and waterproof

In different material versions available

All products in 48h producible

Proof of pressure-tightness

Figure
 
Item number
 
A | Core drill hole
(mm)
B | Pipes / Cables ø
(mm)
L | Seal
(mm)
Material
 
Pressure-tight
(bar)
Thightning torque
(Nm)
Data sheet
 
CRA21107GGV 50 0-25 30 EPDM / GGV 2.5 - PDF
CRA21107V2A 50 0-25 30 EPDM / V2A 2.5 - PDF
CRA21107V4A 50 0-25 30 EPDM / V4A 2.5 - PDF
CRA21108GGV 60 0-35 30 EPDM / GGV 2.5 - PDF
CRA21108V2A 60 0-35 30 EPDM / V2A 2.5 - PDF
CRA21108V4A 60 0-35 30 EPDM / V4A 2.5 - PDF
CRA21109GGV 70 0-45 30 EPDM / GGV 2.5 - PDF
CRA21109V2A 70 0-45 30 EPDM / V2A 2.5 - PDF
CRA21109V4A 70 0-45 30 EPDM / V4A 2.5 - PDF
CRA21110GGV 80 0-55 30 EPDM / GGV 2.5 - PDF
CRA21110V2A 80 0-55 30 EPDM / V2A 2.5 - PDF
CRA21110V4A 80 0-55 30 EPDM / V4A 2.5 - PDF
CRA21111GGV 100 0-75 30 EPDM / GGV 2.5 - PDF
CRA21111V2A 100 0-75 30 EPDM / V2A 2.5 - PDF
CRA21111V4A 100 0-75 30 EPDM / V4A 2.5 - PDF
CRA21112GGV 125 0-100 30 EPDM / GGV 2.5 - PDF
CRA21112V2A 125 0-100 30 EPDM / V2A 2.5 - PDF
CRA21112V4A 125 0-100 30 EPDM / V4A 2.5 - PDF
CRA21113GGV 150 0-125 30 EPDM / GGV 2.5 - PDF
CRA21113V2A 150 0-125 30 EPDM / V2A 2.5 - PDF
CRA21113V4A 150 0-125 30 EPDM / V4A 2.5 - PDF
CRA21114GGV 200 0-175 30 EPDM / GGV 2.5 - PDF
CRA21114V2A 200 0-175 30 EPDM / V2A 2.5 - PDF
CRA21114V4A 200 0-175 30 EPDM / V4A 2.5 - PDF
CRA21115GGV 250 0-225 30 EPDM / GGV 2.5 - PDF
CRA21115V2A 250 0-225 30 EPDM / V2A 2.5 - PDF
CRA21115V4A 250 0-225 30 EPDM / V4A 2.5 - PDF
CRA21116GGV 300 0-275 30 EPDM / GGV 2.5 - PDF
CRA21116V2A 300 0-275 30 EPDM / V2A 2.5 - PDF
CRA21116V4A 300 0-275 30 EPDM / V4A 2.5 - PDF
CRA21117GGV 350 0-325 30 EPDM / GGV 2.5 - PDF
CRA21117V2A 350 0-325 30 EPDM / V2A 2.5 - PDF
CRA21117V4A 350 0-325 30 EPDM / V4A 2.5 - PDF
CRA21118GGV 400 0-375 30 EPDM / GGV 2.5 - PDF
CRA21118V2A 400 0-375 30 EPDM / V2A 2.5 - PDF
CRA21118V4A 400 0-375 30 EPDM / V4A 2.5 - PDF
CRA21119GGV 450 0-425 30 EPDM / GGV 2.5 - PDF
CRA21119V2A 450 0-425 30 EPDM / V2A 2.5 - PDF
CRA21119V4A 450 0-425 30 EPDM / V4A 2.5 - PDF
CRA21120GGV 500 0-475 30 EPDM / GGV 2.5 - PDF
CRA21120V2A 500 0-475 30 EPDM / V2A 2.5 - PDF
CRA21120V4A 500 0-475 30 EPDM / V4A 2.5 - PDF

Problem

You have pipes/cables which must through a waterproof concrete wall. The feed-through must prevent the ingress of odor, gas or water.


Solution (1/4)

Use the Crassus Wall Sleeve PVC with the water pressure-tight vulcanized Power-Profile. Note: The needed size of the wall sleeve (alternative: core drill hole) depends on the size and quantity of the pipes/cables.


Solution (2/4)

Push the Crassus Press Seal Type CMS30 into the cleaned up wall sleeve (alternative: core drill hole) and now you can install the pipes/cables.


Solution (3/4)

Tighten the screws in the following manner, always two diagonally opposite nuts are tightened in succession. Pay attention to the recommended tightening torque.


Solution (4/4)

Done! The feed-through prevents ingress of odor, gas or water.