Press Seal Type DS Blind Insert

Against pressing water and non-pressing water

Water-tight welded bolts for an optimum of steadiness and corrosion protection

100% gas-, odor- and waterproof

For permanent or short-term water-tight sealing

In different material versions available

All products in 48h producible

Proof of pressure-tightness

Figure
 
Item number
 
A | Core drill hole
(mm)
B | Pipes / Cables ø
(mm)
L | Seal
(mm)
Material
 
Pressure-tight
(bar)
Thightning torque
(Nm)
Data sheet
 
CRA21086GGV 80 - 40 EPDM / GGV 3 10.0 PDF
CRA21086V2A 80 - 40 EPDM / V2A 3 10.0 PDF
CRA21086V4A 80 - 40 EPDM / V4A 3 10.0 PDF
CRA21087GGV 100 - 40 EPDM / GGV 3 10.0 PDF
CRA21087V2A 100 - 40 EPDM / V2A 3 10.0 PDF
CRA21087V4A 100 - 40 EPDM / V4A 3 10.0 PDF
CRA21088GGV 125 - 40 EPDM / GGV 3 10.0 PDF
CRA21088V2A 125 - 40 EPDM / V2A 3 10.0 PDF
CRA21088V4A 125 - 40 EPDM / V4A 3 10.0 PDF
CRA21089GGV 150 - 40 EPDM / GGV 3 10.0 PDF
CRA21089V2A 150 - 40 EPDM / V2A 3 10.0 PDF
CRA21089V4A 150 - 40 EPDM / V4A 3 10.0 PDF
CRA21090GGV 200 - 40 EPDM / GGV 3 10.0 PDF
CRA21090V2A 200 - 40 EPDM / V2A 3 10.0 PDF
CRA21090V4A 200 - 40 EPDM / V4A 3 10.0 PDF
CRA21091GGV 250 - 40 EPDM / GGV 3 10.0 PDF
CRA21091V2A 250 - 40 EPDM / V2A 3 10.0 PDF
CRA21091V4A 250 - 40 EPDM / V4A 3 10.0 PDF
CRA21092GGV 300 - 40 EPDM / GGV 3 10.0 PDF
CRA21092V2A 300 - 40 EPDM / V2A 3 10.0 PDF
CRA21092V4A 300 - 40 EPDM / V4A 3 10.0 PDF
CRA21093GGV 400 - 40 EPDM / GGV 3 10.0 PDF
CRA21093V2A 400 - 40 EPDM / V2A 3 10.0 PDF
CRA21093V4A 400 - 40 EPDM / V4A 3 10.0 PDF
CRA21094GGV 500 - 40 EPDM / GGV 3 10.0 PDF
CRA21094V2A 500 - 40 EPDM / V2A 3 10.0 PDF
CRA21094V4A 500 - 40 EPDM / V4A 3 10.0 PDF

Problem

You have to seal a wall sleeve or core drill hole permanent or short-term. The sealing must prevent ingress of odor, gas or water.


Solution (1/4)

Use the Crassus Press Seal Type DS Blind Insert to solve the problem.


Solution (2/4)

Push the Crassus Press Seal Type DS Blind Insert into the cleaned up wall sleeve (alternative: core drill hole).


Solution (3/4)

Tighten the screws in the following manner, always two diagonally opposite nuts are tightened in succession. Pay attention to the recommended tightening torque.


Solution (4/4)

Done! The blind insert ensures an gas- and water-tight seal of the wall sleeve (alternative: core drill hole).